Re: ConnectX-2 EN Digital Optical Monitoring
According to the output, seems that operation is not supported on this HCA.I2C is for debugging purpose only.
View ArticleRe: Mellanox Ethernet Adapters PRM is now available online!
Great news! Are there any plans to release InfiniBand/RoCE PRMs?
View ArticleCQE completed in error - vendor syndrom:216 syndrom:2
Hello, I am trying to port OFED to Barrelfish OS. I mention that I am testing my code on a Mellanox ConnectX-3 Dual-Port NIC (15b3:1003). I started by activating the 2 ports in eth mode and for the...
View ArticleRe: Interoperability problems of the Linux iSER initiator with Windows target...
Hi Ophir,recently we've managed to get Linux iSER initiator working with our target over a pair of directly linked ConnectX-4 EN 100Gbit cards with RoCEv2. But still can't have it working with...
View ArticleMHEH28 on Centos6.8
Hi all, I installed MHEH28 HCA on my workstation (Centos 6.8), and updated the firmware to 2.9.1000.But, I cannot find a driver for MHEH28 on Centos 6.8. Does anyone know where I can find the driver?
View ArticleRe: Red Hat 6.7 + NFS over RDMA
Hi Atul, Per my colleague Ophir, please make sure to follow the procedures documented in the following document.HowTo Configure NFS over RDMA (RoCE) Thank you,Sophie.
View ArticleRe: vSphere host profile creation failed...
Jae-Hoon, Not sure I understand what you mean by "was failed everything". what is the Esxi OS type? Could it be you have import a vSphere host profile with the older driver version not removed? Or did...
View ArticleClik here to view.
Re: vSphere host profile creation failed...
I tried create ESXi 6.0 update 2 host profile from scratch.When I create ESXi host profile with vSphere VPI OFED 1.8.2.4 with SRP target success,but ESXi 6.0 update 2 host profile with vSphere VPI...
View ArticleRe: MHEH28 on Centos6.8
Hi, There is no driver that supports both ConnectX and Centos 6.8 OS.The last driver that supports this type of card is 1.5.3 but it was not tested for Centos 6.8.You can review the following...
View ArticleRe: Issue with Mellanox Connect-X3 Pro cards
Hello Manjunath, Please note that In any Linux based OS there is a file that maps PCI-IDs : /usr/share/hwdata/pci.ids Linux PCI bus low-level driver scans the PCI bus, takes the relevant PCI-IDs over...
View ArticleRe: Connect-X3 PCI Passthrough Issue
Hello, Attempting to attach a PF to a VM when SR-IOV is already enabled on that PF may result in a kernel panic.This is a known issue and currently there is no solution for it. Best Regards.
View ArticleRe: SX1012 ports show "Cable is not present" but cable is connected
Hi The ports should not be locked. Are both ends connected? If not connect both ends and run the command "show interface ethernet <port#>" to check if the port is up. There was a bug in...
View ArticleClik here to view.
Re: Voltaire 500EX-D. Mellanox MHGH28-XTC(DDR) or MHEH28-XTC(SDR)?
Hi Takeshi, What is correct is what is seen in the output of flint. no option to enable DDR
View ArticleRe: MHEH28 on Centos6.8
It seems that I need to downgrade to CentOS 6.2 or older.I appreciate Viki and people in community!!
View ArticleRe: Connectx-4 VPI driver for VMware
I noticed you just announced connectx-5 hardware and you still don't have a working vpi VMware driver for connectx4...
View ArticleRe: Issue with Mellanox Connect-X3 Pro cards
Hi Karen, Even after updating the pci.ids file, the problem still persists.Before and after updating the file /usr/share/misc/pci.ids , the contents remains the same.The content related to Mellanox in...
View ArticleRe: Connect-X3 PCI Passthrough Issue
Hi, Even after disabling the SRIOV in the BIOS, the issue remains same. RegardsManjunath
View ArticleClik here to view.
Re: How can I check ASIC version on my SX6036G
Hi!I didn't tried it yet.I'll test it next July...:)Unfortunately I'm very busy now.If any problem arise in test I'll make a new thread.Best Regard.
View ArticleRe: Mellanox Ethernet Adapters PRM is now available online!
No plans currently, this is available under NDA.
View ArticleRe: Connect-X4 says it doesn't support LINK_TYPE_P1 configuration
Hello Jelte, The reason you are seeing the error is because your card is Ethernet only card(Default is ethernet). You cannot change the port protocol. Cheers,~Rage
View Article