Re: Setup SX1012 without serial
Hi Arjan, You will need to use a Serial to USB adapter.
View ArticleRe: Setup SX1012 without serial
Thanks Eddie, it would be much nicer if Mellanox delivered them by default. Serial devices on laptops are hard to find.
View ArticleRe: Setup SX1012 without serial
hiwould you mind exporting your switches bios/firmware so i can reprogram mine?i can explain how to use flint to do it. (on linux or windows)
View ArticleClik here to view.
Re: mlnx_add_kernel_support.sh and magic version errors.
I have looked through the mlnx_add_kernel_support.sh and mlnxofedinstall to try get this to install properly. So far I have been unsuccessful. I have successfully installed ofed on the following...
View ArticleClik here to view.
Re: Setup SX1012 without serial
I haven't configured anything yet besides the basis stuff like IP addresses.And i don't even know if i will program anything specific to the switches and keep everything default.But i could export the...
View ArticleClik here to view.
Re: Setup SX1012 without serial
This is the adapter I have been using from AmazonHDE USB to Serial Interface Cable with Serial to RJ45 Console Adapter Cable for Cisco Routers
View ArticleRe: OpenFlow ethernet adapter supporting Vswitch
Hi Mehrdad, Do you still need guidance regarding the above?
View ArticleRe: Where to download older Windows drivers?
Hmmm, for WinOF, I'm only seeing version 5.10 on the download page: http://www.mellanox.com/page/products_dyn?product_family=32&mtag=windows_sw_driversAm I looking in the wrong place, or was a typo?
View ArticleRe: MLAG and Spanning Tree
if you will keep the connection between switch 3 and switch 4 while connecting both to the MLAG switches - not sure what will happen.
View ArticleRe: Where to download older Windows drivers?
Just tried the newer WinOF 5.10 drivers. Still no go. The adapter status for both ports says they have no cable plugged in. Which is weird, as one port definitely does, and one doesn't. ibstat...
View ArticleRe: Question about warning banners
Hi Mark, I don't see an option for it. if needed please contact a Mellanox Federal Representative to such a feature.
View ArticleRe: Anyone else seeing ConnectX-3 EN unexpectedly inserting 802.1q tag (VLAN...
Hello Michael, Upgrade the connectX-3 EN to the latest firmware/driver then confirm if you still experiencing the same issue.This seem like an issue unique to your environment. Cheers,~Rage
View ArticleRe: Where to download older Windows drivers?
Didn't manage to get this working from Windows in the end, regardless of what host/switch/etc I plugged into. (IPoIB was definitely enabled in the switch partition when I tried that) Gave up on the...
View ArticleInstalling NEO on CentOS 7
Hi there.I have installed Mellanox NEO on CentOS 7 using neo-1.5.0-7.el7 installation file. End everything went well until I tried to open http://my-server-ip/neo page - it doesn't work. And I didn't...
View Articledirect connection of two servers with IB
Is it possible to directly connect a System x server with a Mellanox ConnectX-3 40GbE / FDR IB VPI Adapter to Dell Server with an IB adapter without going through a IB Switch. If it is what type of...
View ArticleClik here to view.
Re: direct connection of two servers with IB
Hello Juan, You can direct connect servers. If you intend to run in infiniband mode one of those systems will need to be running a subnet manager. for linux you can use opensm. I use this to directly...
View ArticleRe: SRP single dual-port HCA multipath config problem
I see you have installed latest mlnx_ofed driver which is fine, yet suggesting you check in "mlnx_ofed release note for v3.2 (Mellanox website) to see if the Storage vendor you're using is within...
View ArticleClik here to view.
Re: ESX 5.5 U3 upgrade and missing VMNICs
You indicated upgrading to mlnx_ofed_esxi eth driver v1.9.9.4 yet no indication on the fw version of your HP NC543i adapterI would suggest starting with getting the PSID of the adapter, then enter HP...
View ArticleRe: Issues with updating kernel with OFED installed - AttributeError:...
Hello, Uninstall OFED => update kernel => install OFED. Cheers,~Rage
View ArticleRe: ib_send_bw performance puzzle
Hello Weijia, I'm not seeing performance drops on different byte size. Please see below. [root@mti-mar-s5 ~]# ib_send_bw -s 65535 --report_gbits ************************************* Waiting for...
View Article