ethtool -S NIC- and driver-specific statistics
Dear All,Could you please point me to a good document helping to understand the "ethtool -S" output. Which numbers would indicate a problem? Thank you,Aleksandr [root@npectlsqpwfh16...
View ArticleRe: ethtool -S NIC- and driver-specific statistics
Hi,Check this, Counters Troubleshooting for Linux Driver I hope it will help. Ophir.
View ArticleRe: ethtool -S NIC- and driver-specific statistics
Ophir,Thank you! This is great information! Very useful!I was looking at errors ( ifconfig | grep err ), saw "0" and thought that there was nothing to worry about on the NIC level! I have lost 37...
View ArticleRe: Extremely slow ethernet speed with ConnectX VPI card in EN mode.
Did you get these fully working? I'm actually trying to get them to work right with Proxmox 4 (Debian 8.2).
View ArticleMCX312A-XCBT ConnectXR-3 card with Mellanox SFP module 1 Gb Ethernet
Have MCX312A-XCBT ConnectXR-3 card with Mellanox SFP module 1 Gb Ethernet connectedtoCiscoSwitch FastEthernet port. The problem is this:whenthe link lossbetweenSFPmodule andCisco Switch,OSWindowsdoes...
View ArticleClik here to view.
Re: ethtool -S NIC- and driver-specific statistics
Can you check your setup? see here from the OFED manual. Ophir.
View ArticleClik here to view.
Re: iscsi-initiator-utils crashes during boot
Maybe it is a result of some patches from qlogic to add support for their cards, but the bug affects all iscsi modules.You can refer to the following link:Bug 735631 – [iscsiadm] login command may hang...
View ArticleConnectX-2 WOL problem
I am trying to activate WOL on a Connectx-2 EN card. According to firmware pdf: Changes in Rev 2.7.9112 From Rev 2.7.8100• Added WOL over Ethernet support Changes in Rev 2.9.1200 From Rev 2.9.1000•...
View ArticleClik here to view.
Voltaire ISR 9024S-M Firmware and Loading
I just received a older Voltaire ISR 9024S-M.The unit comes up and I have a serial connection to it. All I get is the PPC prompt "=>" and there does not seem to be any firmware on it.The last line I...
View ArticleRe: ethtool -S NIC- and driver-specific statistics
Hi,As last thing, you can check the CPU utilization as well. There are comments there when seeing some of these counters increment is normal. If you are using our Ethernet driver, vport_rx_dropped that...
View Articlecannot config port2 of mellanox mhqh29b-xtr in windows server 2003, connect...
cannot config port2 of mellanox mhqh29b-xtr in windows server 2003, connect cable,but it show media disconnect.the following is like vstat command output,I config the ip of port2 ,but is it appear...
View ArticleRe: cannot config port2 of mellanox mhqh29b-xtr in windows server 2003,...
Can you confirm the Cable is good? And you can try to connect the first cable to the second port , to check if it still have the same issue Thanks
View ArticleRe: cannot config port2 of mellanox mhqh29b-xtr in windows server 2003,...
I am sure the cable is ok, because I change the cable from port 2 to port1 ,it can work, I realize, I donot use a infiniband switch ,and the opensm bind in port1 ,how I need to do with the port2??thanks!!
View ArticleRe: cannot config port2 of mellanox mhqh29b-xtr in windows server 2003,...
port_phys_state=POLLING (2) means physical issue , not because of openSM
View ArticleConfigure SM on SX6036 to match opensmd configuration for OpenStack Mellanox...
I'm deploying a test OpenStack environment using Fuel community edition 6.1 with Mellanox Fuel Plugin, over InfiniBand networking.In order to "free up" an additional node, I'm trying to move my Subnet...
View ArticleRe: Can not install the driver for the Mellanox card on OS Centos 6.5.
seems you upgrade kernel for RHel6.5 So you need use #mlnx_add_kernel_support.sh
View ArticleRe: cannot config port2 of mellanox mhqh29b-xtr in windows server 2003,...
can you tell me how to test the port2? and the physical issue for the port2 is ??thanks!
View ArticleRe: Configure SM on SX6036 to match opensmd configuration for OpenStack...
Hi what is the version of the switch software? The "ib sm allow-both-pkeys" configuration option was added to MLNX-OS 3.4.1120 and above.
View ArticleClik here to view.
MNPH29D-XTR: can I disable RoCE to use both ports for 10G Ethernet
I spent a fair bit of time trying to confirm this in docs and drivers, but I couldn't find the answer...I'd like to disable RoCE functionality on the NIC and use both ports as ordinary 10G NICs.Is that...
View ArticleRe: Voltaire ISR 9024S-M Firmware and Loading
Hi Seth,Seems to me that the switch has a corrupted boot partition and would need to be RMA'd.
View Article